×

SHOPPING FROM

Filter by

Price

0 53

Manufacturers

Type part

more... less
Filter

Rocket R58 group

Rocket R58 group

There are 28 products.

The brewing group on the Rocket R58 espresso machine is a manual E61 style of brewing group. This brewing group is completely based on small compression springs and valve components working together. So a lot of parts of this brewing group are compatible with other E61 style of brewing groups. But not all off them.

There e61 style of brewing group has been build up into 3 sections. The top assembly, the lever mechanism and the drain assembly.

 In the top assembly the water comes in from the brewing group boiler, it flows true a filter and a nozzle. The valve in this section is the one with a round shaft and has a overall length of 55mm.

The lever mechanism is a shaft which pushes the top valve upwards and lets the lower valve go up and vice versa. The handle of this lever mechanism also activates the switch for the pump.

The drain section is made out of 2 valve components. The first drain valve has a square shaft and has a overall length of 52,5mm. the other drain/exhaust valve has a overall length of 27mm.

These valve shafts are not interchangeable with E61 brewing groups used on espresso machines such as Faema, Bezzera and ECM.

The dispensing screen section on the Rocket R58 espresso machine is quite a generic part. Most of these parts such as the portafilter gasket and shower screens are interchangeable with a lot of other e61 brewing groups.

per page
  • 0 1 2 3 4 (0)
    52,48 € Add to cart In Stock

    The drain valve on this page can be used on various E61 style of brewing groups. Models such as ECm, ECM Heidelberg, La Pavoni, Rocket and Vibiemme espresso machines. Not on the Faema E61 This drain valve has been machined from a single piece of brass. After that it has been polished, nickel plated and finally chrome plated. This item is made in Italy....

  • 0 1 2 3 4 (0)
    35,13 € Add to cart In Stock

    The item on this product page is the upper drain sleeve. This drain sleeve can be used with a wide selection of E61 brewing groups. Such as with the brand Faema, ECM, ECM Heidelberg, Isomac, Pavoni, Rocket and San Remo. This drain sleeve has been made from machined brass. This has been afterwards been nickel and chrome plated. The fitting on the inside...

  • 0 1 2 3 4 (0)
    1,61 € Add to cart In Stock

    This stainless steel compression spring is used in the Faema E61 and E61 style brewing groups. But what does this specific do? Well this is the last compression spring in the brewing group. It is the compression spring in the brewing valve which closes the exhaust valve all the way at the bottom of the E61 brewing group. Besides the E61 group spring it...

  • 0 1 2 3 4 (0)
    1,26 € Add to cart In Stock

    This nozzle/gigleur is installed primarily in the brewing group on a espresso machine. It has a hole diameter 0,6mm. There are a variety of diameters available. The thread used on the part is a male M6 with a pitch of 0,75mm. The thread pitch can vary between 0,75mm and 1mm keep that in mind. But also the diameter of the nozzle can vary, so expect when...

  • 0 1 2 3 4 (0)
    2,77 € Add to cart In Stock

    The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...

  • 0 1 2 3 4 (0)
    1,21 € Add to cart In Stock

    This stainless steel compression spring with the dimensions of 15x25mm is normally used as a camme spring on a Faema E61 brewing group or on E61 style brewing groups.  Like with the Faema E61, Faema E61 legend, Grimac, Isomac, Pavoni, Wega and a variety of other brands which use a e61 style of brewing group. Besides that option, this model...

  • 0 1 2 3 4 (0)
    2,52 € Add to cart In Stock

    On this page you will find a camme guide bushing. This part is a generic part for Faema E61 brewing groups and the brewing groups made in the E61 style. This part is made from brass with a total length of 28mm, the outer dimensions are 15 and 10 mm. The ID is 8mm and the head of the bushing has a thickness of 5mm. This part slides over the shaft off the...

  • 0 1 2 3 4 (0)
    5,08 € Add to cart In Stock

    On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....

  • 0 1 2 3 4 (0)
    3,42 € Add to cart In Stock

    This article is one of the earliest designs of the 60mm shower screen. This shower screen is made by IMS CFDR070.  The border diameter is 60mm, it has a internal height of 15,7mm. The internal holes, 112 in total, have a diameter of 2mm Note: this is not a specialty coffee shower, but IMS also produces normal showers. This is, unlike other 60mm...

  • 0 1 2 3 4 (0)
    1,17 € Add to cart In Stock

    The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...

  • 0 1 2 3 4 (0)
    1,10 € Add to cart In Stock

    This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

  • 0 1 2 3 4 (0)
    16,14 € Add to cart In Stock

    This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...

  • 0 1 2 3 4 (0)
    2,77 € Add to cart In Stock

    The drain valve disc on this product page is only used in a few E61 style of brewing groups. You can find them with espresso machine brands such asLa Scala, Bezzera, ECM Heidelberg, La Pavoni, Rocket, Grimac and Isomac. This brass disc can be found at the bottom of the drain of various e61 groups. The brass disc has a outer diameter of 15mm and 8mm. the...

  • 0 1 2 3 4 (0)
    2,29 € Add to cart In Stock

    The o ring on this product page can be used on a variety of espresso machine brands and in various applications. You can find this o ring on brands such as ECM Heidelberg, La Scala, Bezzera, Cimbali, Grimac, La Spaziale, Brasilia and Gaggia. With applications such as water and steam valves and on brewing groups. The part references codes can be found in...

  • 0 1 2 3 4 (0)
    0,59 € Add to cart In Stock

    This gasket is again such a standard type of gasket in the world of espresso coffee machines. It is the EPDM gasket 15.5x7.5x4mm. This gasket is used a variety of applications on espresso machines. Offcourse on the Faema E61 brewing group as well for the E61 style brewing group, as the camme shaft gasket. By brands like Isomac, Bezzera, ECM, Brasilia,...

  • 0 1 2 3 4 (0)
    7,16 € Add to cart In Stock

    The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...

  • 0 1 2 3 4 (0)
    3,34 € Add to cart In Stock

    This portafilter gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 8,5mm. 73x57x8,5mm. This type of brewing group gasket is one of the most standard portafilters around. You will find this on the Faema E61 groups as well as on the E61 style groups used by Vibiemme, La Scala, Bezzera, San Remo, Fiorenzato and Grimac. Of this...

  • 0 1 2 3 4 (0)
    4,09 € Add to cart In Stock

    The item on this product page is a spring guide bushing used on various E61 Style of brewing groups. You can use this item with brands such as ECM Heidelberg, La Scala, Bezzera, Isomac, Pavoni and Brasilia. The Bezzera part reference is 7479942, the Brasilia part reference number is 13657.0.00.04, for ECM Heidelberg it is B7479942, for Isomac ISBUS313116...

Showing 1 - 18 of 28 items
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

Cookie preferences

Functional cookies
No
Yes
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Cookie Provider Purpose Expiry
PHP_SESSIDbrooks-parts.comThe PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser.Session
PrestaShop-#brooks-parts.comThis is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop.480 hours
Advertising Cookies
No
Yes
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
No
Yes
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.
Performance cookies
No
Yes
These are used to improve the browsing experience and optimize the operation of the shop.
Other cookies
No
Yes
These are cookies without a clear purpose or those that we are still in the process of classifying.