×

SHOPPING FROM

Faema E61 camme spring 15x25mm

12-134-L-1250516

>1,21 € VAT incl.
1,00 € without VAT

This stainless steel compression spring with the dimensions of 15x25mm is normally used as a camme spring on a Faema E61 brewing group or on E61 style brewing groups.  Like with the Faema E61, Faema E61 legend, Grimac, Isomac, Pavoni, Wega and a variety of other brands which use a e61 style of brewing group. Besides that option, this model...


0
0/5 - 0 reviews
 Calculate Shipping Cost

    Specifications

    This stainless steel compression spring with the dimensions of 15x25mm is normally used as a camme spring on a Faema E61 brewing group or on E61 style brewing groups.  Like with the Faema E61, Faema E61 legend, Grimac, Isomac, Pavoni, Wega and a variety of other brands which use a e61 style of brewing group.

    Besides that option, this model compression spring is also used on a steam wand on a Marzocco GB5 and FB80.

    But the big question is, what does this spring do as a camme spring? Well this compression spring can be found around the camme shaft. To seal off the camme shaft there are 2 EPDM flat gaskets. To prevent that the gaskets are pressed outwards, by the pump pressure, and leak anyways they have thought of a bushing which is pressed against these gaskets. This pressure comes from the camme compression spring.

    If you are not sure if this compression spring 15x25mm is suitable for your espresso machine brewing group, just send a message and we might be able to help.


    Extra Info

    Outer diameter (OD)15mm
    FaemaFaema E61 Legend S1, Faema E61 Legend S2, Faema E61 Legend S3, E61, E61 legend
    GrimacZola-I, Twenty, Zola-II, Eclisse
    La PavoniBart, Bar, Hotel
    Type partCompression spring
    BrandECM Heidelberg, Vibiemme, Faema, Grimac, La Pavoni, Wega
    part numberVibiemme MOLLPRGO, Pavoni 311421, Faema 4731-135-905, Isomac ISMOLLA-E, ECM C219900427, ECM heidelberg C219900427, Wega WY27421004, BFC 0530095, Royal 0530095, Marzocco F.3.004, Grimac 1180100193-GR788, Futurmat 01854306
    Country of manufacturingMade in Italy

    Reviews (0)

    No customer reviews for the moment.


    Only users who already bought the product can add review.

    Frequently Asked Questions

    Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

    From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

    There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

    The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

    The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

    Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

    We would not advice to do so, seen the capacity is too little to proper function in a bar or a restaurant. For a small office this espresso machine would be a good solution, as well as the use in a kitchen.

    Well this does depend on how old your Bezzera BZ10 is. Seen you have 2 model versions. There is a pre- 26-06-2010 and a post 27-05-2010 version. The older type is in it’s original configuration isn’t available anymore, for this is a relay rebuild kit available which is the same as the new model.

    They are both operated with a Ma-ter pressure switch with is fitted with a safety valve and with a relay. The older ones had a build on relay, but the latest ones have a separate relay.


    This model of Bezzera espresso machine is fitted with a solenoid operated Bezzera ring brewing group, so it hasn’t been fitted with a E61 style of brewing group.

    The Bezzera BZ10 espresso machine is fitted with a water tank, from this tank the water is pumped, with a Ulka vibration pump, towards the brewing group and into the boiler. So you won’t be able to fit a main water connection to this espresso machine.

    The Bezzera BZ10 has been fitted with a double scale pressure gauge, or manometer. So you will see 2 needles, one is for the pump pressure and the other is for the boiler pressure. The boiler pressure goes from 0 up to 3 bar and the pump pressure goes from 0 up to 16 bar.

    Other Products

    This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

    Cookie preferences

    Functional cookies
    No
    Yes
    Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
    Cookie Provider Purpose Expiry
    PHP_SESSIDbrooks-parts.comThe PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser.Session
    PrestaShop-#brooks-parts.comThis is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop.480 hours
    Advertising Cookies
    No
    Yes
    These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
    Analytics cookies
    No
    Yes
    Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.
    Performance cookies
    No
    Yes
    These are used to improve the browsing experience and optimize the operation of the shop.
    Other cookies
    No
    Yes
    These are cookies without a clear purpose or those that we are still in the process of classifying.