Victoria Arduino - Mythos One
Victoria Arduino - Mythos One
There are 14 products.The coffee grinder you will find on this page is the Victoria Arduino Mythos One. This coffee grinder might be one of the most revolutionary grinders made the last decade. This grinder is a “on demand” coffee grinder, this means that this coffee grinder only grounds the coffee you need.
This coffee grinder uses a set of flat grinding burrs, with a right turning direction. The external diameter is 74mm and the internal diameter is 37mm. These grinding burrs can be turned by a 110V motor or a 220/230V model. This is only a single phase mode, there is no 3 phase version of the Mythos One.
What the VA Mythos One so special makes is that this coffee grinder has a heating element at the grinding burrs. This heating element gives more temperature stability at the grinding burrs, which results in more consistency in the ground coffee.
This version only grinds a pre-set amount of coffee once the microswitch at the portafilter fork has been pushed. Seen the Victoria Arduino Mythos 2 has a gravimetric version.
Victoria Arduino Mythos grinder activator...
(0) This type of switch is used on the timer version of the Victoria Arduino Mythos coffee grinder. This specific item is a OEM/original Victoria Arduino spare part. The part reference number for this item is 15030095. You push with your portafilter against this switch, and the grinding process will start.
Eureka / Nuova Simonelli Mythos hopper big
(0) This hopper is especially made for the Eureka and Nuova Simonelli Mythos coffee grinder. This hopper comes as a complete set. The hopper itself, the inner protection on the inside, the lid of the hopper and the shutter to close off the hopper at the bottom. This hopper is suitable for the Eureka Mythos with part number 4000.0000 and the Nuova Simonelli...
Eureka / Nuova Simonelli Mythos PCB display
(0) This electronic display on this page is used in Eureka and Nuova Simonelli coffee grinders. This item is only suitable for the coffee grinder model Mythos. The part contains the display and the 5 push buttons for the dose settings. This item doesn’t come with the membrane. The part number for Nuova Simonelli is 15030011 and the Eureka part number...
Eureka / Nuova Simonelli Mythos burrs...
(0) These original grinding blades can be used on some Eureka and Nuova Simonelli coffee grinders. This item always comes in a Eureka packaging This specific model grinding blades has a base of tool steel base and over it a Titanium layer applied. This layer of Titanium is much harder then the tool steel and has a low friction coefficient. So these blades...
Eureka / Nuova Simonelli burrs 74mm
(0) The grinding blades on this page can be used on a variety of coffee grinders. The brands like Nuova Simonelli (15080002) and the Eureka (MAC74) The outer diameter of this burr is 74mm. The inner diameter of the burr measures 38mm and the thickness measures 9mm. To fix the burrs to the grinder there are 3 mounting holes. The grinding blade is a right...
Eureka / Nuova Simonelli Mythos electronic...
(0) On this page you will find the main electronic device for the Nuova Simonelli Mythos, Eureka Mythos but also on the Victoria Arduino Mythos. This unit is the controller which distributes the power to the vital parts of the coffee grinder. This can only used with a 230V coffee grinder, not with the 110V models made from this specific model. The part...
Eureka / Nuova Simonelli Mythos coffee tray
(0) The coffee collecting tray is a standard item with most coffee grinders. Also, with the Nuova Simonelli and Eureka Mythos. This is a plastic coffee collecting tray which slides into the frame of the coffee grinder. It can be removed easily to clean the coffee collecting tray The part number for the Eureka Mythos is 4100.0009 and for the Nuova...
Eureka / Nuova Simonelli burrs holder bottom
(0) This burr holder is used on a couple of coffee grinder brands. Nuova Simonelli (15080009 ) and Eureka(2520.0005). On this part the bottom burr (15030057) is also attached with 3 screws. This is also the rotating burr, seen it is attached to the motor shaft. On which grinders can I use this burr holder? On the Nuova Simonelli MDL, Nuova Simonelli...
Switch 5 poles 16A 250V
(0) On this page you will find a black bipolar switch with a red indicator light in it. This is quite a common switch model; you can find this model on a variety of espresso machines and coffee grinders. this switch is rated at 16A at 250V. This switch mounts in a hole with the dimensions 22x30mm Brands which use this type of switch in their espresso...
Nuova Simonelli/Victoria Arduino Mythos 1...
(0) This item is a grinding burr holder, used on the Victoria Arduino and the Nuova Simonelli Mythos one. This item has Nuova Simonelli part reference number 15030097 and the Victoria Arduino part reference number 15030097. This grinding burr holder has been made in Italy
Nuova Simonelli/Victoria Arduino Mythos...
(0) This set of coffee grinding burrs can be used on various Nuova Simonelli and Victoria Arduino coffee grinders. The Nuova Simonelli part reference number is 15080002 and for Victoria Arduino this is 15080002. This set of grinding burrs is a OEM/Original set of Nuova Simonelli grinding burrs. The outer diameter of these grinding burrs is 75mm. You can use...
Nuova Simonelli/Victoria Arduino Capacitor...
(0) This capacitor is a OEM/Original spare part for Nuova Simonelli and Victoria Arduino coffee grinders. The Part reference number for this item is 15030027 This specific capacitor is used on the 110V versions of the Mythos grinders. It produces 60uf and it is used for single phase motors. This capacitor has been made in Italy.
Nuova Simonelli/Victoria Arduino Mythos...
(0) This microswitch is used on Nuova Simonelli and Victoria Arduino Mythos coffee grinders. This switch indicates if the coffee hopper is installed, otherwise the grinder won’t work. The part reference number for this item is 15030002.This microswitch is rated up to 10A at 250V
Victoria Arduino Mythos grind adjustment knob
(0) You may adjust the coffee grinder's grind setting to a finer or coarser degree with this knob. With the reference number 15030098, you can tell this is an authentic, original equipment manufacturer (OEM) spare part. The Mythos, Mythos one, and Mythos two, as well as the Victoria Arduino, are just a few of the types that can make use of this adjustment knob.
