28-026-L-1523538
>8,70 € VAT incl.7,19 € without VAT
tax incl.
Specifications
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands.
This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned earlier, this valve is made from a low lead content brass, CW510L.
For which coffee machine brands can you use this type of anti vacuum valve? Brands like Conti, Wega, Astoria, Faema, Grimac, La Cimbali, ECM Heidelberg, Casadio, La Carimali and Marzocco.
Extra Info
Astoria CMA | Argenta, Brava, Denise, Dora, Lisa, Pratic, Rapallo, Vania, Gloria, CK, CKE, CKX, CKXE |
Faema | E61 Jubile, E61 legend, Faema E61 Jubilé A1, Faema E61 Jubilé A2, Faema E61 Legend S1, Faema E61 Legend S2, Faema E61 Legend S3 |
Casadio | Dieci, Dodici, Venti |
La Carimali | Systema, Eco, Uno |
Grimac | Mia, Ten, Twenty |
Type part | Anti vacuum valve |
part number | Cimbali 418-911-002, Cimbali 418-932-000, Cimbali 418911002, Faema 418911002, Cimbali 418932000, Faema 3161-134654, Faema 3161134654, Marzocco L190, Wega WY56150 |
Reviews (0)
No customer reviews for the moment.
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.
Cookie | Provider | Purpose | Expiry |
---|---|---|---|
PHP_SESSID | brooks-parts.com | The PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser. | Session |
PrestaShop-# | brooks-parts.com | This is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop. | 480 hours |