Grimac G10 parts

The expansion valve gasket shown on this page is a generic item. You can find it in the catalogue of a variety of espresso machine manufacturers. The gasket is a flat NBR gasket with a pin at the end. The widest section of the gasket has a diameter of 15mm and the pin has a diameter of 6mm. The total height for the gasket is 10mm. Which espresso machine...

The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...

This a universal Polytetrafluoroethylene (PTFE) gasket with 22x16x2mm. The gasket is used on a variety of espresso machine components. This type of gasket found boilers, brewing group and valve assemblies. The most common location for this to seal off the 3/8” male nut on the top of the Faema E61 and E61 style brewing groups like with Bezzera, Brasilia,...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

O ring 7.2x1.9mm epdm

In some cases, the shower screen is attached with a screw, in most cases that is a Philips or a slotted screw. It is difficult to remove it with a regular screwdriver due to the limited height under the brew group.  But for that you need a shortened slotted screwdriver, in this case the one from the German brand Wera, which fits well under the brewing...

The steam wand on this page is a OEM/Original Grimac/Fiorenzato spare part. these are the same companies. The Grimac part reference number for this item is A2000090, for Fiorenzato it is the identical number. This steam valve comes as a complete set, so tube, steam tip and fixing nut. The steam tip has in total 4 holes. This steam tube can be used on...

The rotation pump on this page is made by the Italian manufacturer Fluid o tech, the pump type is designated as model “Standard” with the Fluid o tech manufacturer code: PA0104AGANN0000 This model of rotation pump is a clamp ring type. The pump face and motor face are pushed against each other and a stainless-steel clamp is place around it....

The item on this product page is a small compression spring which is used on various espresso machine brands such as Brasilia and Grimac. The Brasilia part references are 00884.0.00.03 and 0088400003. For Grimac the references are 1180100035 and C295. This compression valve is used on steam and water valves. The outer diameter is 11mm and the...

On this page you will find a colourful double scale manometer which is suitable for various Grimac espresso machine models. The Grimac part reference number for this item is 1250200033-GR034S The left side shows the pump pressure from 0 to 15 bar and on the right side the boiler pressure from 0 to 2.5bar. The body of this pressure gauge has a diameter of...

The item on this product page is a steam wand which can be used on various Grimac espresso machines. The part reference numbers are 1260200031 and GR211. This steam wand comes as ready to install assembly. This item comes with the nut, tube and the steam tip. This item has been made in Italy. This steam tube can be used on the Grimac G10, Grimac Zola I,...