Faema Portafilter gasket 74x58x8mm Original
€4.43 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
The portafilter gasket ton this product page is a OEM/Original Faema spare part, but can also be used on various Casadio espresso machine models. The Casadio part reference number is 402199010, the Faema part reference numbers are402199000, 402199010 and 4701016528.
This gasket is made from NBR. The outer diameter is 74mm the inner diameter is 58mm and the thickness is 8mm. There are 3 internal cuts. The gasket has been made in Italy.
You can use this portafilter gasket on the Casadio Dafne, Casadio Dieci, Casadio Quindici, Casadio Undici, Faema E61, Faema E61 Jubile, Faema E61 Legend, Faema Emblema, Faema E71, Faema E92, Faema Enova, Faema Smart, Faema Teorema, Faema E64, Faema E98.
Data sheet
- Brand
- Faema
- Casadio
- Dafne
Dieci
Quindici
Undici - Country of manufacturing
- Made in Italy
- Faema
- Due
Due A
Due S
E61
E61 Jubile
E61 legend
E64
E66
E71
E91
E92
E97
E98
Emblema
Emblema A
Emblema S
Emblema restyling A
Emblema restyling S
Enova
Enova S
Express
Faema E61 Jubilé A1
Faema E61 Jubilé A2
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3
Smart
Smart A
Smart A restyling
Smart S
Smart S restyling
Teorema A
Teorema S - part number
- Casadio 402199010
Faema 402199000
Faema 402199010
Faema 4701016528 - Portafilter gasket inner dimension (mm)
- 58
- Portafilter gasket outer dimension (mm)
- 74
- Portafilter gasket thickness (mm)
- 8
- Type
- Original
- Type part
- Portafilter gasket
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.