Brewing group gigleur 0.6mm
search
  • Brewing group gigleur 0.6mm

Brewing group gigleur 0.6mm

€1.26
Tax included

€1.04 tax excl.

qty
Last items in stock

compare
  Security policy

(edit with the Customer Reassurance module)

  Delivery policy

(edit with the Customer Reassurance module)

  Return policy

(edit with the Customer Reassurance module)

This nozzle/gigleur is installed primarily in the brewing group on a espresso machine. It has a hole diameter 0,6mm. There are a variety of diameters available. The thread used on the part is a male M6 with a pitch of 0,75mm. The thread pitch can vary between 0,75mm and 1mm keep that in mind. But also the diameter of the nozzle can vary, so expect when you install a 0,7mm nozzle you will get a lot more water volume out of the group.

This specific type of nozzle can be used on brewing groups made by models like: Expobar, Faema, Futuremat, Grimac, Pavoni, La Scala, Vibiemme and wega.

If you are not sure if your brewing group has a similar screw thread type of which nozzle diameter you need to have. Just send us a message true the contact page and we might be able to help you with this.

12-093-L-1501566
2 Items

Data sheet

Faema
E61
E61 Jubile
E61 legend
Faema E61 Jubilé A1
Faema E61 Jubilé A2
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3
part number
Expobar 30200061
Faema 4151135890
Futurmat 02446706
Grimac 1201600005-F213
Scala C-0314
Vibiemme RACCGIES7
Wega W10308
Vibiemme
Chimaera
Cubo
Domobar
Domobar Junior
Domobar Super
Dosaplus
Evolution
Kometa
Lollo
Mercury
Minimax
Replica
Revolution
Silver
Is a vintage E61 steam valve the same as the modern steam valves? insert_link

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

Are there differences between the Faema E61 brewing groups? insert_link

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

How many types of boilers are there on the Faema E61? insert_link

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Is the Faema E61 espresso machine suitable for a busy bar/café insert_link

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Comments (0)
No customer reviews for the moment.

8 other product