Faema E61 group upper plug
€3.38 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
On the top of a Faema E61 brewing group or a E61 brewing group is always the final item. That’s a chrome plated 3/8” male plug. Nothing else nor something special.
This is generic part which can also be used in a variety of situations then a E61 brewing group, but also on different locations on a espresso machine. Like on the boiler with a Vibiemme espresso machine.
But the main locations where you find the chrome plated 3/8” nut is on the E61 style brewing groups used by: Grimac, Bezzera, La Scala, Vibiemme, Brasilia, Wega, La Pavoni and ECM Heidelberg.
If you are not sure if the chrome plated 3/8”nut is suitable for your coffee machine. Just send a message to us that we can verify this
Data sheet
- Brand
- Bezzera
Brasilia
ECM Heidelberg
Faema
Grimac
La Pavoni
La Scala
San Remo
Vibiemme
Wega - Brasilia
- Century
Gradisca
Portofino - Country of manufacturing
- Made in Italy
- Faema
- E61
E61 Jubile
E61 legend
Faema E61 Jubilé A1
Faema E61 Jubilé A2
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3 - Fitting thread 1
- 3/8" M
- Grimac
- Eclisse
Ten
Twenty
Zola-I
Zola-II - part number
- BFC 0520000
Bezzera 7479952
Brasilia 12791.0.10.04
ECM R000002141
ECM heidelberg R000002141
Faema 4142135892
Futuremat 02446201
Grimac 2231000001-GR713
Isomac ISTAP3136184
Orchestrale D27118
Pavoni 3136184
Reneka AT7479952
Royal 0520000
San Remo 10052137A
Scala C-0317
Vibiemme RACCTACHCASU
Wega WY27118 - Type part
- Brewinggroup fitting
- Vibiemme
- Chimaera
Cubo
Domobar
Domobar Junior
Domobar Super
Dosaplus
Evolution
Kometa
Lollo
Mercury
Minimax
Replica
Revolution
Silver - Wega
- Airy
Antares
Colosseum
Combinova
Espressa
Euro-2000
Formula-Milano
Junior
Mininova
Nova
Novecento
Orion Eco
Polaris
Sphera
Syntesis
Vela
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.