Grimac فئة الجزء

The compression spring on this product page is used in various steam and water valves. Brands which used this model of compression spring where ECM Heidelberg, Vibiemme and La Scala. The part references are for Vibiemme MOLLTUVA, MOLTUVA and  MOLTUVARUBEVO. For ECM Heidelberg the part reference number is P6003.13  This stainless steel...

The drain valve on this page can be used on various E61 style of brewing groups. Models such as ECm, ECM Heidelberg, La Pavoni, Rocket and Vibiemme espresso machines. Not on the Faema E61 This drain valve has been machined from a single piece of brass. After that it has been polished, nickel plated and finally chrome plated. This item is made in Italy....

On this product page you will find a dosing device which can be used on the Grimac Mia 1 group espresso machine. The Grimac part reference for this item is MG282 – 1040200001. The Gicar reference number for this is 9.5.17.84G00. the name of the item is 30uz R/E 230Vac and it runs on 230Vac

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...

The dosing device on this page can be used on the Grimac Twenty espresso machine. The Grimac part reference for this item is GRW156 - 1040200013  The name of this dosing device is DOS7 RL3 2GR+RL+THE 240V The dosing device has been manufactured by the Italian company Giemme, the part reference for this item is 01.13.0124

في بعض الحالات ، يتم ربط شاشة الاستحمام بمسمار ، في معظم الحالات يكون هذا مسمار فيليبس أو مسمار مقفل. من الصعب إزالته بمفك عادي بسبب الارتفاع المحدود تحت مجموعة الشرب. ولكن من أجل ذلك تحتاج إلى مفك المسامير المختصرة، في هذه الحالة من العلامة التجارية الألمانية Wera، والتي تناسب بشكل جيد تحت مجموعة البيرة بحيث يكون من السهل فك المسامير وأنها لا تنزلق. مفك...

Copper gasket 20x24x1,5mm

On this page you will find one of the most used brewing group solenoid valves in espresso machines. But this is instead of a 230V version a 115V version. This solenoid valve has been manufactured by the company Parker. The Parker parts reference for this solenoid valve is 393106J or 393111J This 3-way solenoid valve is a model with a flat flange, this...

This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...

The solenoid valve on this page is a 3 way solenoid valve, mainly with the application as a brewing group solenoid valve.  Parker has listed this part under 471012 and 471013 The coil used on this solenoid valve is a 9W 220/240V which runs on 50/60Hz. The coil number for this solenoid valve is 483510S6 The valve in question is a 3 way solenoid...

The flowmeter on this page is one of the most commonly used flowmeters in espresso machines. This flowmeter has been manufactured by the Italian company Gicar, so also made in Italy. In the extra field tab next to this text you will see a entire list of compatibilities with other models and brands. This specific flowmeter does not come with a fixed wire,...

The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...