Faema E61 plug for camme holder
€5.88 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
This ½” chrome plated stuffing nut has a central hole of 10,7mm. The item itself has a height of 17mm. You need a metric key 22 to install this item. This is quite a common key size in most peoples toolbox. But what is the function of this part and where can it be found.
This threaded stuffing gland is used in the side of the Faema E61, Faema E61 Legend and E61 style brewing groups. To seal off the EPDM seals which seal off the camme shaft you first have a brass bushing which pushes against the EPDM gaskets. The pressure comes from a 15x25mm camme shaft compression spring. This compression spring presses against the inside of this chrome plated stuff gland. It is basically a seat for a compression spring.
This specific item is used on a variety of brewing groups like the E61 and Style used by: Vibiemme, Bezzera, Faema, La Pavoni, La Scala, Futurmat and Brasilia.
Are you not sure if this chrome plated stuffing nut is suitable for your brewing group, just send us a message to verify?
Data sheet
- Bezzera
- Galatea
- Brand
- Bezzera
Faema
Grimac
La Pavoni
La Scala
Vibiemme
Wega - Brasilia
- Century
Gradisca
Portofino - Country of manufacturing
- Made in Italy
- Faema
- E61
E61 legend
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3 - Grimac
- Eclisse
Ten
Twenty
Zola-I
Zola-II - La Scala
- Butterfly
Eroica
Iris - part number
- Bezzera 7479971
Brasilia 13653.0.10.04
Faema 4152135906
Futurmat 01878909
Grimac 1230800036-GR786
Isomac ISTAPPRGOCR
Pavoni 3132064
Reneka AT7479971
Scala C-0035
Vibiemme RACCTAPRGO
Wega WY27421023 - Type part
- Brewinggroup fitting
- Vibiemme
- Cubo
Domobar
Domobar Junior
Domobar Super
Replica - Wega
- Airy
Antares
Atlas
Colosseum
Combinova
Espressa
Euro-2000
Formula-Milano
Junior
Mininova
Novecento
Orion Eco
Polaris
Sphera
Syntesis
Vela
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.