Gasket AFM 34 22x16x2mm
€1.00 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
The most common location for this to seal off the 3/8” male nut on the top of the Faema E61 and E61 style brewing groups like with Bezzera, Brasilia, Grimac, La Scala, Vibiemme and Wega.But also as a gasket to seal off boiler components with brands like Vibiemme and Grimac,
This gasket has been made from the material AFM 34 made by the german company Victor Reinz. This gasket has a outer diameter of 22mm a inner diameter of 16mm and a thickness of 2mm. This gasket has been made in Germany
Are you not sure if this is the correct component for your espresso machine, please send us a message to check if it is the correct part.
Data sheet
- Bezzera
- Galatea Domus
- Brasilia
- Gradisca
Portofino - Country of manufacturing
- Made in Germany
- Faema
- E61
E61 Jubile
E61 legend - Gasket Material
- AFM34
- Grimac
- Eclisse
G10
G11
Mia
Twenty
Zola-I
Zola-II - part number
- Astoria 12023
Bezzera 7479935
Brasilia 04360.0.00.02
Brasilia 0436000002
ECM C469900421
ECM heidelberg C469900421
Fiorenzato A1200152
Grimac 1110300021
Grimac F036A
Grimac F055T
Grimac GR719
Grimac P262
Grimac VBM020
Grimac W538
Grimac W538A
Isomac ISGUATF35302
Pavoni 362026
Reneka AT7479935
San Remo 10502090A
Vibiemme GUARCAINGRTE
Wega W10643
Wega WY12023 - Vibiemme
- Chimaera
Cubo
Domobar
Domobar Junior
Domobar Super
Dosaplus
Evolution
Kometa
Lollo
Minimax
Replica
Revolution
Silver
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.