55-422
>1,21 € VAT incl.1,00 € without VAT
tax incl.
Specifications
The most common location for this to seal off the 3/8” male nut on the top of the Faema E61 and E61 style brewing groups like with Bezzera, Brasilia, Grimac, La Scala, Vibiemme and Wega.But also as a gasket to seal off boiler components with brands like Vibiemme and Grimac,
This gasket has been made from the material AFM 34 made by the german company Victor Reinz. This gasket has a outer diameter of 22mm a inner diameter of 16mm and a thickness of 2mm. This gasket has been made in Germany
Are you not sure if this is the correct component for your espresso machine, please send us a message to check if it is the correct part.
Extra Info
Gasket Material | AFM34 |
Brasilia | Portofino, Gradisca |
Bezzera | Galatea Domus |
Faema | E61, E61 Jubile, E61 legend |
Grimac | G10, G11, Mia, Zola-I, Zola-II, Twenty, Eclisse |
La Pavoni | Bart, Bar, Hotel |
Vibiemme | Cubo, Domobar, Domobar Super, Domobar Junior, Dosaplus, Chimaera, Replica, Revolution, Evolution, Kometa, Lollo, Minimax, Silver |
part number | Bezzera 7479935, Reneka AT7479935, Astoria 12023, Wega WY12023, Brasilia 04360.0.00.02, Brasilia 0436000002, ECM C469900421, ECM heidelberg C469900421, Fiorenzato A1200152, Grimac 1110300021, Grimac F036A, Grimac F055T, Grimac GR719, Grimac P262, Grimac VBM020, Grimac W538, Grimac W538A, Isomac ISGUATF35302, Pavoni 362026, San Remo 10502090A, Vibiemme GUARCAINGRTE, Wega W10643 |
Country of manufacturing | Made in Germany |
Reviews (0)
No customer reviews for the moment.
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.
We would not advice to do so, seen the capacity is too little to proper function in a bar or a restaurant. For a small office this espresso machine would be a good solution, as well as the use in a kitchen.
Well this does depend on how old your Bezzera BZ10 is. Seen you have 2 model versions. There is a pre- 26-06-2010 and a post 27-05-2010 version. The older type is in it’s original configuration isn’t available anymore, for this is a relay rebuild kit available which is the same as the new model.
They are both operated with a Ma-ter pressure switch with is fitted with a safety valve and with a relay. The older ones had a build on relay, but the latest ones have a separate relay.
This model of Bezzera espresso machine is fitted with a solenoid operated Bezzera ring brewing group, so it hasn’t been fitted with a E61 style of brewing group.
The Bezzera BZ10 espresso machine is fitted with a water tank, from this tank the water is pumped, with a Ulka vibration pump, towards the brewing group and into the boiler. So you won’t be able to fit a main water connection to this espresso machine.
The Bezzera BZ10 has been fitted with a double scale pressure gauge, or manometer. So you will see 2 needles, one is for the pump pressure and the other is for the boiler pressure. The boiler pressure goes from 0 up to 3 bar and the pump pressure goes from 0 up to 16 bar.
Cookie | Provider | Purpose | Expiry |
---|---|---|---|
PHP_SESSID | brooks-parts.com | The PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser. | Session |
PrestaShop-# | brooks-parts.com | This is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop. | 480 hours |