Anti vacuum valve V.A.R. 1/4"
€7.19 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands.
This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned earlier, this valve is made from a low lead content brass, CW510L.
For which coffee machine brands can you use this type of anti vacuum valve? Brands like Conti, Wega, Astoria, Faema, Grimac, La Cimbali, ECM Heidelberg, Casadio, La Carimali and Marzocco.
Data sheet
- Astoria CMA
- Argenta
Brava
CK
CKE
CKX
CKXE
Denise
Dora
Gloria
Lisa
Pratic
Rapallo
Vania - Casadio
- Dieci
Dodici
Venti - Faema
- E61 Jubile
E61 legend
Faema E61 Jubilé A1
Faema E61 Jubilé A2
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3 - Grimac
- Mia
Ten
Twenty - La Carimali
- Eco
Systema
Uno - part number
- Cimbali 418-911-002
Cimbali 418-932-000
Cimbali 418911002
Cimbali 418932000
Faema 3161-134654
Faema 418911002
Faema 3161134654
Marzocco L190
Wega WY56150 - Type part
- Anti vacuum valve
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.