Faema E61 valve gasket 13x4x4mm
search
  • Faema E61 valve gasket 13x4x4mm

Faema E61 valve gasket 13x4x4mm


€0.59
Tax included

€0.49 tax excl.

qty

  Security policy

(edit with the Customer Reassurance module)

  Delivery policy

(edit with the Customer Reassurance module)

  Return policy

(edit with the Customer Reassurance module)

The valve gasket on this page can be used on numerous of espresso machine brands such as Vibiemme, Wega, La Scala, Faema, La Pavoni, Brasilia and Grimac. This gasket in mainly used in the steam and water valves as well as in the water inlet valves. But the best example is in the E61(type) of brewing groups. The part reference list can be found in the extra info tab.

This gasket has been made from NBR. The outer diameter is 13mm the inner diameter is 4mm and the thickness if 4mm. This gasket has been made in the Czech Republic.

You can use this gasket for instance on the Faema E61, Faema E61 Legend, Grimac G11, Grimac Zola, Vibemme Replica, Vibiemme Domobar, Vibiemme Lollo, La Scala

28-077-L-1186311
834 Items

Data sheet

Country of manufacturing
Made in Czech Republic
Faema
Due
E61
E61 Jubile
E61 legend
E91
E92
Lambro
Marte
Mercurio
President
Urania
Gasket Material
NBR
Grimac
Eclisse
Ten
Twenty
Zola-I
Zola-II
Inner diameter (ID)
4mm
Outer diameter (OD)
13mm
part number
Astoria 27421008
Astoria 27421026
Brasilia 12005.0.00.02
Faema 4701-019545
Faema 2151136654
Faema 4701019545
Pavoni 362027
Rancilio 36301008
Rancilio 36302002
San Marco 109051
Vibiemme GUARPI
Vibiemme GUARPIEVOREVO
Wega W10343
Wega WY27421008
Wega WY27421026
Thickness
4mm
Type part
Gasket
Vibiemme
Chimaera
Cubo
Domobar
Domobar Junior
Domobar Super
Dosaplus
Evolution
Kometa
Lollo
Mercury
Minimax
Replica
Revolution
Silver

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Comments (0)
No customer reviews for the moment.

8 other product