Fluidotech clamp ring pump 200L/H
search
  • Fluidotech clamp ring pump 200L/H
  • Fluidotech clamp ring pump 200L/H

Fluidotech clamp ring pump 200L/H


€96.07
VAT included

€79.40 tax excl.

qty
Shipment after 4 - 8 working days

  Security policy

(edit with the Customer Reassurance module)

  Delivery policy

(edit with the Customer Reassurance module)

  Return policy

(edit with the Customer Reassurance module)

On this product page you will find a brass espresso machine pump. This pump can be used on espresso machine brands such as Astoria and Wega. The part references for this rotation pump is for Astoria 26303 and for Wega WY26303 

This rotary vane espresso machine pump has been made by the Italian company Fluid o Tech. This model is a clamp on type, so it is installed with clamping a stainless steel spring between the motor and pump. The flowrate for this pump is 200 L/H. the pump itself has been equipped with a balanced bypass. The compatible fitting type is a 3/8” BSP-G thread. This pump has been made in Italy.

You can use this fluid o tech pump on the Astoria Plus 4 You, Astoria CK, Astoria CKE, Astoria CKX, Astoria CKXE, Wega Combinova, Wega Junior, Wega Compatta, Wega Airy, Wega Sphera, Wega Nova and the Wega Atlas

Astoria
19-027-L-1330026

Data sheet

Astoria CMA
CK
CKE
CKX
CKXE
Plus 4 You
Brand
Astoria
Wega
Certification
NSF
part number
Brasilia 04321.4.00.08
Brasilia 04321.4.00.09
Brasilia 0432140008
Cimbali 533-191-600
Cimbali 533191600
Nuova Simonelli 01300006
Promac 69000285
Rancilio 69000266
San Marco 202001
San Remo 10252070A
San Remo 10252072A
San Remo 10252072B
Victoria Arduino 01300006
Wega WY26303
Pump flowrate (L/H)
200
Type part
Rotation pump
Type pump
Rotary vane
Wega
Airy
Atlas
Combinova
Junior
Sphera

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Comments (0)
No customer reviews for the moment.

8 other product