Faema E61 gasket PTFE 36.5x30x2mm
€0.62 tax excl.
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
(edit with the Customer Reassurance module)
This PTFE gasket can be used on the famous Faema E61 brewing groups, but also on a variety of E61 style of brewing groups. Like with La Scala, Grimac, Pavoni, Wega and Fiorenzato. The part reference numbers can be found in the extra info tab.
This flat gasket is made from the material PTFE. The outer diameter is 36,5mm and the inner diameter is 30mm and has a thickness of 2mm. This PTFE gasket is made in Italy.
You can use this gasket on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Pavoni Bar, Pavoni Bart, Pavoni Pub, Grimac Mia, Grimac Zola, Grimac G10, Wega Airy, Wega Combinova, Wega Espressa, Wega Polaris, Wega Sphera, Wega Nova and the Wega Orion.
Data sheet
- Brand
- Faema
Grimac
La Pavoni
La Scala
Wega - Country of manufacturing
- Made in Italy
- Faema
- E61
E61 Jubile
E61 legend
Faema E61 Jubilé A1
Faema E61 Jubilé A2
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3 - Grimac
- Ten
Twenty
Zola-I
Zola-II - Inner diameter (ID)
- 30mm
- La Pavoni
- Bar
Bart
Pub - La Scala
- Butterfly
Carmen
Eroica
Iris
Norma
Tosca - part number
- Faema 4701135912
Pavoni 362026
Wega W10643
Wega WY12023 - Thickness
- 2mm
- Wega
- Airy
Antares
Atlas
Colosseum
Combinova
Espressa
Euro-2000
Formula-Milano
Junior
Mininova
Nova
Novecento
Orion Eco
Polaris
Sphera
Syntesis
Vela
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.