Portafilter gasket 73x57x8,5mm
search
  • Portafilter gasket 73x57x8,5mm

Portafilterpakning 73x57x8,5mm


€ 3.13
Inklusive MVA

€ 2.59 eks. mva.

qty

  GDPR-overholdelse

Beskytte dine personlige data

  Fraktpolicy

Alt om frakt av bestillingen din

  Returpolicy

alle inns og outs om vår returpolicy

Portfilterpakningen på denne sida vert brukt på ulike Wega espressomaskinmodell. Den Wega delreferanse for dette elementet er WY12228.

Denne portafilterpakningen er laga av NBR. Denne pakningen har ein ytre diameter på 73 mm, ein indre diameter på 57 mm og ei tykkelse på 8,fem millimeter. Det er tre skår på innsida. Denne pakningen er laga i Italia.

Du kan bruka denne filterhaldaren på ein rekke Wega espresso-maskinmodell som Wega Det er eit godt stykke, Wega Antares, Wega Colosseum, Wega Euro 2000, Wega Formel Milano, Wega Polaris, Wega Syntesis, Wega Kom inn i gong. For den komplette oversikten over modellen kan du sjå på mer informasjon.



Orchestrale
49-038-L-1186895

Dataark

delenummer
Wega WY12228
Merke
Orchestrale
Wega
Pakningsmateriale
NBR
Portafilter pakningstykkelse (mm)
8.5
Portafilterpakning indre dimensjon (mm)
57
Portafilterpakning ytre dimensjon (mm)
73
Produksjonsland
Made in Italy
Type del
Portafilter gasket
Wega
Airy
Antares
Atlas
Colosseum
Combinova
Espressa
Euro-2000
Formula-Milano
Junior
Mininova
Nova
Novecento
Orion Eco
Polaris
Sphera
Start
Syntesis
Vela

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Kommentarer (0)
Ingen kundeanmeldelser enda.

Related Product

8 other product