E61 brewing group gasket rebuild kit
search
  • E61 brewing group gasket rebuild kit

Faema E61 brewing group gasket rebuild kit

€ 22.96
Inklusive MVA

€ 18.98 eks. mva.

qty
Siste varer på lager

compare
  GDPR-overholdelse

Beskytte dine personlige data

  Fraktpolicy

Alt om frakt av bestillingen din

  Returpolicy

alle inns og outs om vår returpolicy

Setet for gjenoppbygging av pakkingar på denne produktsida kjem med forbrenningsvara som vert brukt på Faema E61 ei bryggjergruppe. Så dette komplette settet kan ikkje brukast på andre E61 mange av dei er kompatible, men ikkje alle. I dei fleste tilfelle treng du ikkje å skifta ut messingartiklane i bryggegruppen din, fordi dei slitas mindre fort enn pakkingane.

Dette kitet inneheld 18 ulike objekt. Lista nedan viser desse elementane:

1x dusjskjerm gammal modell;

3x 13x4x4mm ventilpakking

2x 15.5x7.5x4mm støyting av aksle

1 x pakking 22x16x2mm

3x pakking 36x30x2mm

1x o ring 3.53x18.64mm.

1 x pakking 26x21x2mm

1 x portfilterpakking 74x57x8mm

1 x portfilterpakking 73x57x8,5 mm

1 x portfilterpakking 73x57x9mm

1x papirslim 0,8 mm

1x papirslim 0,5 mm

1x vannfilter 11 mm

Dette settet med pakkingar kan brukast på vintage Faema E61 espresso maskin Faema E61 Legend brewing grupper og på solenoid dreiv Faema E61 Jubile. Du brukar berre ikkje heile paklinga.

50-792
1 Artikkel
Is a vintage E61 steam valve the same as the modern steam valves? insert_link

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

Are there differences between the Faema E61 brewing groups? insert_link

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

How many types of boilers are there on the Faema E61? insert_link

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Is the Faema E61 espresso machine suitable for a busy bar/café insert_link

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Kommentarer (0)
Ingen kundeanmeldelser enda.

8 other product