€ 104.60 eks. mva.
GDPR-overholdelse
Beskytte dine personlige data
Fraktpolicy
Alt om frakt av bestillingen din
Returpolicy
alle inns og outs om vår returpolicy
Den roterende svelgen til espresso-maskinen pumpa. Det finst ulike merke som produserer slike pumpar som Fluid o tech, Nuert og Procon. Du kan ikkje. Pumpa på denne sida er laga av selskapet Procon. Du kan ikkje. Delnummer 132A060F123B
Pumpen på denne sida vert kalla ein roterende svein klemp pumpe. Pumpa er fest på ein flange med ein rustfritt stålklem. Viss du strammar denne klemmen, vil pumpa knyta til motoren. Ver alltid oppmerksom på kva slags akselforbinding pumpen har, dette er ein standard firkantaksel som er egnet for dei fleste espresso maskinmotorar.
Denne spesifikke pumpemodellen har ein flytfrekvens på 180 l/h og har ein balansert bypass. Motoren er NSF-sertifisert
Fittings som vert brukt på denne pumpa er 3/8” NPT i staden for 3/8BSP-G brukt av Fluid o tech og Nuert.
På sida av pumpen finn du ein liten justeringsskru, der du kan justera trykk på pumpen, om du vil økja trykk skru det innover og redusere trykk skru det utover.
På kva slags espresso-maskinmerke kan du bruka denne pumpa? Dette varierer frå Astoria, Gaggia,Grimac, Magister, La Pavoni, Rancilio, San Marco, Vibiemme til Wega.
Men viss du ikkje er sikker, så send oss eit bilde av pumpen din og detaljer om kaffemaskinen, så kan vi hjelpa deg å finne den rette pumpen for kaffemaskinen din
Dataark
Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.
From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.
There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.
The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.
The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.
Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.
