The brewing group which is used on the Rocket Appartamento is of the type called the E61 style of brewing group. This brewing group originates from the Faema E61 brewing group, but does have quite some design changes so some components are not interchangeable.
On this brewing group the water enters on the top side of the group head. This first flows true a wire mesh filter into a small nozzle. Then it enters the first brewing chamber. In this chamber you will find a valve, with a overall length of 55mm. This valve is held in place with a compression spring.
The next section is the lever assembly. In this assembly you have a shaft, when you move the lever up you will push the valve above(55mm) open and the water will flow out of the brewing group.
When you lower, close the top valve, the lever assembly. The drain valve will be pushed open. The drain valve is made up out of 2 valve types. The top one is a drain valve with a length of 52,5mm, with at the end a square shaft. The lower valve is the drain valve, which has a length of 27mm. From this valve all the exhaust water will flow out of the brewing group.
The components which are located where you lock the portafilter in place are quite generic for E61 brewing groups. The portafilter gasket has a outer diameter of 73mm and a inner diameter of 57mm. the shower screen is just a standard 60mm wire mesh screen.
If you are not entirely sure which components you need for your Rocket Appartamento brewing group, don’t hesitate to contact us.This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...
The gasket on this product page can be used on various Bezzera steam and water valves. The Bezzera part reference code for this item is 5493023 This gasket has been made from EPDM. The outer diameter is 19mm, the inner diameter is 3,5mm and the thickness is 4mm This gasket has been made in Czech Republic. This steam and water valve gasket can be...
The drain valve disc on this product page is only used in a few E61 style of brewing groups. You can find them with espresso machine brands such asLa Scala, Bezzera, ECM Heidelberg, La Pavoni, Rocket, Grimac and Isomac. This brass disc can be found at the bottom of the drain of various e61 groups. The brass disc has a outer diameter of 15mm and 8mm. the...
The o ring on this product page can be used on a variety of espresso machine brands and in various applications. You can find this o ring on brands such as ECM Heidelberg, La Scala, Bezzera, Cimbali, Grimac, La Spaziale, Brasilia and Gaggia. With applications such as water and steam valves and on brewing groups. The part references codes can be found in...
On this page you will find a o ring which has a cord diameter of 2,62mm and a internal diameter of 20,63mm. the material for this o ring is Viton. The application in espresso machines for this o ring is really broad. This ranges from application in brewing groups with brands like ECM Heidelberg, la Scala, Bezzera and Brasilia. But also the application in...
The valve gasket on this page can be used on numerous of espresso machine brands such as Vibiemme, Wega, La Scala, Faema, La Pavoni, Brasilia and Grimac. This gasket in mainly used in the steam and water valves as well as in the water inlet valves. But the best example is in the E61(type) of brewing groups. The part reference list can be found in the...
This gasket is again such a standard type of gasket in the world of espresso coffee machines. It is the EPDM gasket 15.5x7.5x4mm. This gasket is used a variety of applications on espresso machines. Offcourse on the Faema E61 brewing group as well for the E61 style brewing group, as the camme shaft gasket. By brands like Isomac, Bezzera, ECM, Brasilia,...
The o ring on this page can be used on various espresso machine brands such as San Marco, Bezzera, Cimbali, Gaggia, ECM Heidelberg. The part reference numbers of this o ring can be found in the extra info tab. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 9,92mm. This o ring is made in Italy. You can use this o...
The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...
This portafilter gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 8,5mm. 73x57x8,5mm. This type of brewing group gasket is one of the most standard portafilters around. You will find this on the Faema E61 groups as well as on the E61 style groups used by Vibiemme, La Scala, Bezzera, San Remo, Fiorenzato and Grimac. Of this...
The item on this product page is a spring guide bushing used on various E61 Style of brewing groups. You can use this item with brands such as ECM Heidelberg, La Scala, Bezzera, Isomac, Pavoni and Brasilia. The Bezzera part reference is 7479942, the Brasilia part reference number is 13657.0.00.04, for ECM Heidelberg it is B7479942, for Isomac ISBUS313116...
The portafilter gasket on this page can be used on various espresso machine models such as ECM Heidelberg, La Pavoni, Rocket and Wega. The part references for this item are for La Pavoni 361014, for ECM Heidelberg C449900229 , for Rocket C449900229 and for Wega W10321/ WY12227 This portafilter gasket has been made from NBR with shore 75....
The drain valve on this page is used in a variety of E61 style of brewing groups. You will find this model of drain valve assembly on brands such as Bezzera, ECM Heidelberg, Isomac, La Pavoni, Brasilia, Grimac and Royal. This drain valve comes pre-assembled. The assembly contains the triangular shaped shaft, gasket holder, gasket, flat washer and the...
the single portafilter on this product page can be used on various Rocket espresso machines. The Rocket part reference for this item is A699905020 This single portafilter has a ear orientation of 90 degree. The thickness of the ears of this portafilter is 5,7mm. The portafilter does come with a stainless steel spring and a single filterbasket. This...
The portafilter on this product page can be used on a variety of Rocket espresso machines. The Rocket part reference for this item is A699905021. This portafilter is a 2 coffee model. The ear orientation of this portafilter is 90 degree. The thickness of these ears is 5,7mm. The spout used is a 2 coffee one, which is closed but with a removable...
This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal...
Cookie | Provider | Purpose | Expiry |
---|---|---|---|
PHP_SESSID | brooks-parts.com | The PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser. | Session |
PrestaShop-# | brooks-parts.com | This is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop. | 480 hours |