Rocket Appartamento group
Rocket Appartamento group
There are 44 products.The brewing group which is used on the Rocket Appartamento is of the type called the E61 style of brewing group. This brewing group originates from the Faema E61 brewing group, but does have quite some design changes so some components are not interchangeable.
On this brewing group the water enters on the top side of the group head. This first flows true a wire mesh filter into a small nozzle. Then it enters the first brewing chamber. In this chamber you will find a valve, with a overall length of 55mm. This valve is held in place with a compression spring.
The next section is the lever assembly. In this assembly you have a shaft, when you move the lever up you will push the valve above(55mm) open and the water will flow out of the brewing group.
When you lower, close the top valve, the lever assembly. The drain valve will be pushed open. The drain valve is made up out of 2 valve types. The top one is a drain valve with a length of 52,5mm, with at the end a square shaft. The lower valve is the drain valve, which has a length of 27mm. From this valve all the exhaust water will flow out of the brewing group.
The components which are located where you lock the portafilter in place are quite generic for E61 brewing groups. The portafilter gasket has a outer diameter of 73mm and a inner diameter of 57mm. the shower screen is just a standard 60mm wire mesh screen.
If you are not entirely sure which components you need for your Rocket Appartamento brewing group, don’t hesitate to contact us.E61 chromed group collector
(0) The drain valve on this page can be used on various E61 style of brewing groups. Models such as ECm, ECM Heidelberg, La Pavoni, Rocket and Vibiemme espresso machines. Not on the Faema E61 This drain valve has been machined from a single piece of brass. After that it has been polished, nickel plated and finally chrome plated. This item is made in Italy....
E61 upper pipe
(0) The item on this product page is the upper drain sleeve. This drain sleeve can be used with a wide selection of E61 brewing groups. Such as with the brand Faema, ECM, ECM Heidelberg, Isomac, Pavoni, Rocket and San Remo. This drain sleeve has been made from machined brass. This has been afterwards been nickel and chrome plated. The fitting on the inside...
Compression spring 14x33mm
(0) This stainless steel spring 14x33mm is used in a variety of locations in a espresso machine. The most common location for this compression spring is in a Faema E61 brewing group of a E61 style brewing group. The spring seats inside the top trumpet and makes sure that the top brewing valve closes when the brewing process is stopped, and the lever has...
Compression spring 13x42mm
(0) This stainless steel compression spring is used in the Faema E61 and E61 style brewing groups. But what does this specific do? Well this is the last compression spring in the brewing group. It is the compression spring in the brewing valve which closes the exhaust valve all the way at the bottom of the E61 brewing group. Besides the E61 group spring it...
Portafilter gasket 73x57x9mm
(0) Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr) The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these...
Brewing group gigleur 0.6mm
(0) This nozzle/gigleur is installed primarily in the brewing group on a espresso machine. It has a hole diameter 0,6mm. There are a variety of diameters available. The thread used on the part is a male M6 with a pitch of 0,75mm. The thread pitch can vary between 0,75mm and 1mm keep that in mind. But also the diameter of the nozzle can vary, so expect when...
Filterholder suplement gasket 73x59x0.8mm
(0) The paper shim on this page is one of the most widely used paper shim. You can use this type with a wide selection of espresso machine brewing groups. What are the dimensions of this paper shim? They have a outer diameter of 73mm, a inner diameter of 59mm and a thickness of 0,8mm. What does a paper shim do? Brewing group locking mechanisms wear due to...
Stainless steel filter 8.6x22.5mm
(0) The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...
Faema E61 group valve guide 11mm
(0) This model small brass square pin can be found in the oldest E61 brewing groups, the ones used on the Faema E61. This specific model can only be used on Faema E61 models and the ones used on Wega espresso machines. The Faema part reference for this item is 4161135915 and for Wega the part references are W10341 and WY27421013. This brass square...
Faema E61 camme spring 15x25mm
(0) This stainless steel compression spring with the dimensions of 15x25mm is normally used as a camme spring on a Faema E61 brewing group or on E61 style brewing groups. Like with the Faema E61, Faema E61 legend, Grimac, Isomac, Pavoni, Wega and a variety of other brands which use a e61 style of brewing group. Besides that option, this model...
Faema E61 sleeve
(0) On this page you will find a camme guide bushing. This part is a generic part for Faema E61 brewing groups and the brewing groups made in the E61 style. This part is made from brass with a total length of 28mm, the outer dimensions are 15 and 10 mm. The ID is 8mm and the head of the bushing has a thickness of 5mm. This part slides over the shaft off the...
E61 style group spout breaker
(0) On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....
E61 shower screen old style 60mm
(0) This article is one of the earliest designs of the 60mm shower screen. This shower screen is made by IMS CFDR070. The border diameter is 60mm, it has a internal height of 15,7mm. The internal holes, 112 in total, have a diameter of 2mm Note: this is not a specialty coffee shower, but IMS also produces normal showers. This is, unlike other 60mm...
Faema E61 plug for camme holder
(0) This ½” chrome plated stuffing nut has a central hole of 10,7mm. The item itself has a height of 17mm. You need a metric key 22 to install this item. This is quite a common key size in most peoples toolbox. But what is the function of this part and where can it be found. This threaded stuffing gland is used in the side of the Faema E61,...
PTFE gasket 35x30x2mm
(0) The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...
Filterholder gasket 72.5x57x8 mm
(0) The portafilter gasket on this product page can be used with a wide selection of brands. This portafilter gasket can be used on Brasilia, San Remo, la Scala, Bezzera, Faema, Vibiemme and Pavoni espresso machines. This gasket has been made from NBR. The outer diameter is 72,5mm, the inner diameter is 57mm and the thickness is 8mm. This gasket has been...
