This plastic bushing is designed for use in the washing arm assemblies of Colged dishwashers and glasswashers. With an external diameter of 14 mm, a 7 mm hole, and a height of 10 mm, it enables smooth movement and helps prevent wear during operation. Compatible with a wide range of ISYTECH, STEELTECH, and TOPTECH models.
External diameter: ø14 mm
Hole diameter: ø7 mm
Height: 10 mm
Low-friction plastic for smooth rotation
Suitable for commercial dishwashing systems
Made in Italy
Compatibility
Colged
Dishwasher
ISYTECH38-10 D, ISYTECH38-11 D, ISYTECH38-12 D, ISYTECH38-13 D
Looking for similar items or different specifications for this Colged plastic bushing for washing arm ø14 × ø7 × 10 mm?
Explore our full range in the Horeca category
*
This part is compatible to the original part number. Part numbers are always leading.
Details
60-360-5111848
Data sheet
Type
Compatible (non-original)
Review
Comments (0)
No customer reviews for the moment.
Your review appreciation cannot be sent
Report comment
Are you sure that you want to report this comment?
Report sent
Your report has been submitted and will be considered by a moderator.
Your report cannot be sent
Write your review
Review sent
Your comment has been submitted and will be available once approved by a moderator.
We are Brooks-Parts and sell spare parts for Horeca machines. This
pack of 10 thermocouples SIT M8x1 (60 cm each) is
made in Italy, providing consistent heat management across
multiple gas-fueled appliances.
Unless listed as OEM, items are compatible replacements.
This black shower connection features a standard 1/2" AG (male) thread and is suitable for use in professional kitchen environments. Designed with durability in mind, it comes with the GASTROTOP logo and is manufactured in China.
Made in China
Includes GASTROTOP branding
Standard 1/2" AG thread
Ideal for integration with pre-rinse units,...
The Electronic Circuit Board 215034-5 is a high-performance component designed for commercial dishwashers. With dimensions of 137x80 mm, this board ensures efficient operation and reliable performance for a wide range of dishwashers from AMIKA, COLGED, DIAMOND, ELETTROBAR, and WOLK.
Key Features:
Dimensions: 137x80 mm
High-quality electronic...
This fastening screw (ø 7 mm) locks the arm assembly in place inside Krupps dish units. It keeps the spray arm secure during each wash and rinse cycle. Built for daily use in pro kitchen setups where clean results and tight parts are a must.
Made with strong-grade steel, tested for heat and pressure. Made in Italy and 100% OEM.
Main features:
OEM part –...
The Mareno OEM CR0581710 knob is a genuine control knob for a wide range of Mareno
professional appliances. It is used on front panels to adjust heat output or operating settings, providing safe,
precise and comfortable control during daily HoReCa service.
This original Mareno knob is designed for a shaft diameter D 6 (6 mm) and is supplied as...
PEL 777090, 777111, and 777120 Gas Tap 21/S valves deliver reliable pilot-flame ignition with a Ø 21 mm pipe-flange inlet, M16×1.5 mm outlet, M9×1 thermocouple port, and D-shaped pin Ø 8×6.5 mm for precise, leak-proof installation.
Key Features
Pilot Flame Port: Continuous ignition support
Standard Fittings: Ø 21 mm flange inlet and M16×1.5 mm...
This 440 mm rinse arm assembly is made in Italy and built for high-performance commercial dishwashers and glasswashers. Crafted for durability and consistent water flow, it’s compatible with a wide selection of machines by AMIKA, COLGED, EUROWASH, and WOLK.
Key Features:
Length: 440 mm
Made in Italy
Durable stainless steel construction
Ensures...
Optimize liquid flow control in your ice machines with this rugged, intermittent-duty solenoid valve from Deltrol Controls.
Key Features
Model: 2LSX-240M (74017-69)
Voltage: 208–240 V AC, 50/60 Hz
Power: 12 W
Cycle: Intermittent duty
Inlet Fitting: Hose end ø 17.4 mm
Outlet Fitting: ø 16 mm...
