La Scala

The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from...

The 2 coffee filterbasket on this page can be used a big variety of espresso machine brands. You can use this basket on brands such as Casadio, Brugnetti, ECM Heidelberg, San Remo, Faema, Vibiemme, La Scala, Grimnac. This filterbasket has been made by the Italian company IMS Filtri. The IMS part reference is CF2T068. Note: this is not a competition...

This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...

Faema E61 steam/water valve gasket holder

The valve gasket on this page can be used on numerous of espresso machine brands such as Vibiemme, Wega, La Scala, Faema, La Pavoni, Brasilia and Grimac. This gasket in mainly used in the steam and water valves as well as in the water inlet valves. But the best example is in the E61(type) of brewing groups. The part reference list can be found in the...

On this page you will find a 110V 3 way solenoid valve made by the Italian manufacturer ODE. This specific model 31A1AR15 is made in Italy. This model is a flange solenoid valve. So it is bolted with 4 Allen bolts against a flat surface and is sealed of by 2 o rings at the bottom. In the brass body of the solenoid valve, you will find a orifice of 1,5mm....

The fitting on this product page is the last fitting on various E61 style of brewing groups. The drain fitting. This item can be used on various brands which use the E61 group, such as Faema, Grimac, La Pavoni, Rocket and Wega. This drain fitting has been made from machined brass. Which has been polished, nickel and chrome plated. The thread on one side...

The Italian solenoid manufacturer ODE is currently the only espresso machine solenoid manufacturer who makes some of their solenoid from the Techno polymer PPS. On this page you see a 3 way solenoid valve made from PPS with the part number 31APBA1R15-13T0 As mentioned before this is a 3 way solenoid valve with a flange. This flange mates against a other...

The item on this page is a hardened steel bush used on various steam and water valves. This item can be used on brands such as Vibiemme, Marzocco, ECM Heidelberg and Fiorenzato. The ECM Heidelberg part reference number is P6003.2, for Fiorenzato it is A2200265, for Marzocco it is B.1.004/2 and for Vibiemme it is RACCINSRUBLOL. This steel bushing has...

The portafilter gasket shown on this product page is one of the most common sizes found on commercial espresso machines. But this gasket hasn’t been made from NBR as traditionally done, but from food grade silicone. You can find this portafilter gasket on brands such as Faema, Vibiemme, Bezzera and La Scala. This red silicone gasket has a outer diameter...

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr) The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...

The single filterbasket model shown on this page is mainly used on Astoria and Wega espresso machines. Note: this basket can be used on any portafilter which has a similar 70mm outer diameter filterbasket. This single coffee filterbasket has been made by the Italian filterbasket manufacturer IMS Filtri, their reference number for this item is CM1T007....