Filter by
Manufacturers
Type part
more... less
Type
Price
Filter

Rocket R58 espresso machine

This espresso machine is one of the few dual boiler coffee machines around, especially for a domestic coffee machine. But at some point in life the Rocket R58 will also break down and seals start to leak. On this page you can find the most of the parts for the Rocket R58 espresso machine

Rocket R58 espresso machine parts

Faema E61 valve gasket 15,5x7,5x4mm

This gasket is again such a standard type of gasket in the world of espresso coffee machines. It is the EPDM gasket 15.5x7.5x4mm. This gasket is used a variety of applications on espresso machines. Offcourse on the Faema E61 brewing group as well for the E61 style brewing group, as the camme shaft gasket. By brands like Isomac, Bezzera, ECM, Brasilia,...
€0.74
Quick-view

Portafilter gasket 73X57X8.5mm

This portafilter gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 8,5mm. 73x57x8,5mm. This type of brewing group gasket is one of the most standard portafilters around. You will find this on the Faema E61 groups as well as on the E61 style groups used by Vibiemme, La Scala, Bezzera, San Remo, Fiorenzato and Grimac. Of this...
€4.19
Quick-view

E61 shower screen old style 60mm

This article is one of the earliest designs of the 60mm shower screen. This shower screen is made by IMS CFDR070.  The border diameter is 60mm, it has a internal height of 15,7mm. The internal holes, 112 in total, have a diameter of 2mm Note: this is not a specialty coffee shower, but IMS also produces normal showers. This is, unlike other 60mm models, a...
€4.29
Quick-view

Portafilter gasket 73x57x8mm

The portafilter gasket on this page can be used on various espresso machine models such as ECM Heidelberg, La Pavoni, Rocket and Wega. The part references for this item are for La Pavoni 361014, for ECM Heidelberg C449900229 , for Rocket C449900229 and for Wega W10321/ WY12227  This portafilter gasket has been made from NBR with shore 75. This portafilter...
€3.95
Quick-view

Solenoid valve silicone o ring 6,07x1,78mm

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.66
Quick-view

PTFE gasket 26x21x2mm

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....
€1.38
Quick-view

PTFE gasket 35x30x2mm

The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...
€1.47
Quick-view

Rocket on off switch 16A 250V

On this product page you will find a on off switch suitable for various Rocket espresso machine models. This switch is in the style of old rocket switches. This switch is connected with the body panel with a M12 which has a pitch of 1mm. This switch is rated up to 16A at 250V. There are 4 connecting terminals. The Part references of Rocket for this...
€13.54
Quick-view

Heating element gasket PTFE 42x33x3mm

On this page you will find a PTFE heating element gasket is suitable for a variety of brands such as ECM Heidelberg and Bezzera This heating element gasket has a outer diameter of 42mm a inner diameter of 33mm and a thickness of 3mm. This size of gasket is suitable for a 1” screw in heating element.
€3.40
Quick-view

Stainless steel filter 8.6x22.5mm

The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...
€3.47
Quick-view

E61 style group spout breaker

On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....
€6.37
Quick-view

Drain valve assembly

The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...
€8.99
Quick-view

PTFE gasket 21x16.8x2mm

The PTFE gasket on this page can be used on a variety of espresso machines brands and various applications. You will mainly find this gasket as a seal with water and steam valves, but you can also find them in brewing groups. This PTFE gasket has a outer diameter of 21mm a inner diameter of 16,8mm and a thickness of 2mm. You can use this flat gasket in...
€0.99
Quick-view

Brewing group gigleur 0.6mm

This nozzle/gigleur is installed primarily in the brewing group on a espresso machine. It has a hole diameter 0,6mm. There are a variety of diameters available. The thread used on the part is a male M6 with a pitch of 0,75mm. The thread pitch can vary between 0,75mm and 1mm keep that in mind. But also the diameter of the nozzle can vary, so expect when...
€1.58
Quick-view

Contact thermostat 135°C with M4 thread

On this product page you will find a contact thermostat which is used on a variety of espresso machine brands. You can find this contact thermostat on Bezzera and Rocket espresso machines. The Bezzera part reference is 7434009 and the Rocket part reference is C199901550 This contact thermostat is set at 135°C and is a manual reset model. The contact...
€10.71
Quick-view

Faema E61 group infusion spring

On this page you will find a stainless steel compression spring with a outer dimension of 14mm and a length at rest of 45mm. This compression spring is being used in a variety of espresso machine brewing groups. This ranges from the famous Faema E61 brewing group, the E61 style brewing group. But also a variety of other type of brewing groups used by...
€1.62
Quick-view

E61 style camme rod

This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...
€20.25
Quick-view

Boiler safety valve 3/8" 1.8 bar CE-PED

The boiler safety valve shown on this page can be used on wide selection of espresso brands such as Brasilia, Wega, Astoria, Grimac, Cimbali, Faema, Marzocco and Carimali. The part references can be found on the extra info tab. This boiler safety valve has a male 3/8” BSP-G thread. The safety valve has been set at 1,8 bar, this is not adjustable. When the...
€28.63
Quick-view

PTFE gasket 18x13x2mm

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...
€1.15
Quick-view

Drain valve pre-assembled 52,8mm

The drain valve on this page is used in a variety of E61 style of brewing groups. You will find this model of drain valve assembly on brands such as Bezzera, ECM Heidelberg, Isomac, La Pavoni, Brasilia, Grimac and Royal. This drain valve comes pre-assembled. The assembly contains the triangular shaped shaft, gasket holder, gasket, flat washer and the...
€15.01
Quick-view

O ring silicone 2,62x21,89mm

The o ring on this product page can be used on a various espresso machine brands and with various applications. You can find this type of o ring with Rocket and La San Marco espresso machines. For Rocket they are used in the steam and water valves. For San Marco in various brewing groups. The rocket part references are A449904672 and A449905151. For San...
€1.32
Quick-view

Compression spring 13x42mm

This stainless steel compression spring is used in the Faema E61 and E61 style brewing groups. But what does this specific do? Well this is the last compression spring in the brewing group. It is the compression spring in the brewing valve which closes the exhaust valve all the way at the bottom of the E61 brewing group. Besides the E61 group spring it is...
€2.02
Quick-view

E61 upper pipe

The item on this product page is the upper drain sleeve. This drain sleeve can be used with a wide selection of E61 brewing groups. Such as with the brand Faema, ECM, ECM Heidelberg, Isomac, Pavoni, Rocket and San Remo. This drain sleeve has been made from machined brass. This has been afterwards been nickel and chrome plated. The fitting on the inside is...
€30.34
Quick-view

AFM 34 gasket 26x21x2mm

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....
€1.16
Quick-view

Technical features on the Rocket R58

The Rocket R58 has quite a lot of technical features installed. In this case you mainly need to think of electronic temperature control. Most espresso machines make use of temperature control with a pressure switch

Dual boiler

The Rocket R58 espresso machine has, as one of the few, a double boiler. You normally only see this on the commercial high end espresso machines. But now on the Rocket R58 coffee machine. The small boiler, which has a 1400W heating element, is used for the water for the brewing group.

The boiler used for the steam and water boiler is a heating element, with the same wattage of 1400W, which has a different design the ones used on the coffee boiler. The total of 2800W of heating power is plenty enough of heating power.

E61 brewing group

The Rocket R58 is also fitted with a manual E61 style of brewing group, as you see with most domestic Rocket espresso machines. A lot of the parts used on the E61 style of brewing groups are universal, but there are also various which are unique to the brand Rocket.

Pump and motor

Where most domestic espresso machines, also from Rocket, use a Ulka vibration pump. The Rocket R58 doesn’t use a vibration pump. They use a pump and motor assembly. The motor is made by the Italian company RPM and the pump is made by Fluid o tech, but if you have a pump with similar specs you can also use that one as well.

Water tank

The water tank on the back of the Rocket R58 makes it possible that you don’t have to have a main water connection.  From this water tank the water is pumped into the water boilers of the espresso machine. This needs to be pumped, seen the boilers are pressurized.

Maintenance on your Rocket R58

Keeping your Rocket R58 espresso machine is good working condition is very important if you want to keep the quality of your espresso at a high level. Besides that keeping your coffee machine clean will also result in extending the longevity of the espresso machine.

Backflushing your brewing group

Backflushing your brewing group should be a daily routine if you want to keep your espresso machine in the best possible condition. For this you will need a blind filter filterbasket and a cleaner, such as the Puly Caff powder. For full instructions on how to clean your brewing group just check out Blog posts about this topic.

Descaling your boilers

With a typical Heat Exchanger (HX) espresso machine boiler it is possible that you descale your espresso machine via the water tank. But in the case of a dual boiler espresso machine we do advice to not do this. The most important thing is that you use a proper water filter for your Rocket R58, note: this does not prevent the build up of scale, but reduces a lot.

 

Rocket Milano R58 parts from Brooks

At Brooks we sell a variety of spare parts for the Rocket R58 espresso machine. This can be OEM/original spare parts, but also a variety of aftermarket parts. If you are not entirely sure which components you need for your espresso machines, don’t hesitate to contact us.