E61 brewing group complete rebuild kit
search
  • E61 brewing group complete rebuild kit

Faema E61 brewing group rebuild kit


€55.79

€55.79 tax excl.

qty
Last items in stock

  GDPR Compliance

Protecting your personal data

  Shipping policy

Everything about shipping your order

  Return policy

all the inns and outs about our return policy

On this product page you will find a rebuild kit for Faema E61 espresso machines. The Faema E61 brewing group is the basis off all the other E61 style of brewing groups made. This does not mean that this kit will fit all those brewing groups.

Manufacturers have made over time a lot of changes in the brewing group assemblies, so they are for some percentage interchangeable. If you are not sure which machine you have and what kit you might need, don’t hesitate to contact us.

This Faema E61 rebuild kit contains in total 36 items. Below you can find a parts list:

QT

Article

1

Complete spout valve 53mm

1

Spring 13x42mm

1

O ring mushroom 3,53x18,64mm

1

Gigleur/nozzle

1

Filter holder bushing brass

1

Stainless filter 11mm

1

Flat washer

1

Top nut gasket ptfe 22x16x2mm

1

Gigleur spring 8x20mm

1

Cam spring 15x25mm

1

Cam guide busing 28mm

2

EPDM flat gasket 15,5x7,5x4mm

1

Camshaft 82mm without pin

1

Spray nozzle brass 30mm m10x1

1

Paper filler 0,5mm

1

Paper filler 0,8mm

1

Portafilter gasket 9mm

1

Portafilter gasket 8,5mm

1

Portafilter gasket 8mm

1

Shower screen

1

Drain valve square

1

Stainless spring 14x45mm

3

PTFE gasket 36x30x2mm

1

Drain valve assembly

1

Spring 14x33mm

1

Drain jet brass

1

PTFE Gasket 26x21x2mm

 

50-791
1 Item

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Comments (0)
No customer reviews for the moment.

8 other product