Faema E61 group spout breaker
search
  • Faema E61 group spout breaker

Faema E61 group spout breaker


€6.13

€6.13 tax excl.

qty
Last items in stock

  GDPR Compliance

Protecting your personal data

  Shipping policy

Everything about shipping your order

  Return policy

all the inns and outs about our return policy

The fitting on this product page is the last fitting on various E61 style of brewing groups. The drain fitting. This item can be used on various brands which use the E61 group, such as Faema, Grimac, La Pavoni, Rocket and Wega.

This drain fitting has been made from machined brass. Which has been polished, nickel and chrome plated. The thread on one side is a ½”BSP-G thread. The total length of this item is 36mm. The item has been made in Italy.

You can use this item on the Faema E61, Faema E61 Legend, Pavoni Bar, Pavoni Bart, Rocket Appartamento, Rocket R58, Grimac Eclisse, Grimac Twenty. For the complete list of part references and models check the extra info tab.

12-131-L-1439006
1 Item

Data sheet

Brand
Faema
Grimac
La Pavoni
Wega
Country of manufacturing
Made in Italy
Faema
E61
E61 legend
Faema E61 Legend S1
Faema E61 Legend S2
Faema E61 Legend S3
Fitting thread 1
1/2" M
Grimac
Eclisse
Twenty
Zola-I
Zola-II
La Pavoni
Bar
Bart
Pub
part number
Faema 4152135921
Grimac 1231000014-F205
Pavoni 3140744
Wega WY27421018
Type part
Brewinggroup fitting
Wega
Airy
Antares
Atlas
Colosseum
Combinova
Espressa
Euro-2000
Formula-Milano
Junior
Mininova
Nova
Novecento
Orion Eco
Polaris
Sphera
Syntesis
Vela

Well that answer is pretty simple, no it isn’t. The original valve works as following, when you turn the shaft inwards the valve pin will push a gasket holder. The steam can go out, close it again and no steam can go out. In the case of the modern E61 valves is that behind the gasket holder is a small stainless steel ball with a spring.

From the beginning of the Faema E61 brewing group are basically no differences between the parts installed inside the brewing group. Parts such as the valve gaskets, springs, valve assemblies and portafilters have all remained the same. The biggest change is the small cleaning hole on the front of the brewing group. With the earliest models this hole didn´t exist.

There are 5 types of boiler used on the Faema E61 espresso machine. The most well known is the double flanged model. You have on one side the heating element flange and on the other side the water level flange, both are out of production. These are held in place with aluminium boiler rings. For the single groups you have a boiler with a flange on one side.

The next model is a stainless steel boiler, with one flange. This type of boiler is less common then the copper boiler above. There is also a later model stainless steel, which doesn’t have a removable flange. Both these boilers have corrosion issues, this has to do because of the stainless steel.

The latest model is also a copper boiler, this boiler has a single heat exchanger(HX) in the middle. Most modern espresso machines have for each individual brewing group a individual HX.

Yes it is, but this depends on various factors. The first thing is experience, seen this is a manual operated espresso machine it requires a lot more attention from the barista then a solenoid operated model. There you need to stop the brewing process manually. If you don’t have the experience you probably can’t hold up with the tempo which is required at such a bar. Then I would advice to go for the Faema E61 Jubilee, this is the solenoid operated version of the Faema E61 Legend espresso machine.

Comments (0)
No customer reviews for the moment.

8 other product