×

SHOPPING FROM

Filter by

Price

0 90

Manufacturers

Type part

more... less

Voltage

more... less
Filter

Vibiemme Domobar Junior 2B group

Vibiemme Domobar Junior 2B group

There are 41 products.

Vibiemme Domobar Junior 2B group parts

per page
  • 0 1 2 3 4 (0)
    52,48 € Add to cart In Stock

    The drain valve on this page can be used on various E61 style of brewing groups. Models such as ECm, ECM Heidelberg, La Pavoni, Rocket and Vibiemme espresso machines. Not on the Faema E61 This drain valve has been machined from a single piece of brass. After that it has been polished, nickel plated and finally chrome plated. This item is made in Italy....

  • 0 1 2 3 4 (0)
    4,02 € Add to cart In Stock

    The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this...

  • 0 1 2 3 4 (0)
    1,43 € Add to cart In Stock

    This stainless steel spring 14x33mm is used in a variety of locations in a espresso machine. The most common location for this compression spring is in a Faema E61 brewing group of a E61 style brewing group. The spring seats inside the top trumpet and makes sure that the top brewing valve closes when the brewing process is stopped, and the lever has...

  • 0 1 2 3 4 (0)
    1,61 € Add to cart In Stock

    This stainless steel compression spring is used in the Faema E61 and E61 style brewing groups. But what does this specific do? Well this is the last compression spring in the brewing group. It is the compression spring in the brewing valve which closes the exhaust valve all the way at the bottom of the E61 brewing group. Besides the E61 group spring it...

  • 0 1 2 3 4 (0)
    3,33 € Add to cart In Stock

    Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr) The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these...

  • 0 1 2 3 4 (0)
    1,26 € Add to cart In Stock

    This nozzle/gigleur is installed primarily in the brewing group on a espresso machine. It has a hole diameter 0,6mm. There are a variety of diameters available. The thread used on the part is a male M6 with a pitch of 0,75mm. The thread pitch can vary between 0,75mm and 1mm keep that in mind. But also the diameter of the nozzle can vary, so expect when...

  • 0 1 2 3 4 (0)
    0,68 € Add to cart In Stock

    This a universal Polytetrafluoroethylene (PTFE) gasket with 22x16x2mm. The gasket is used on a variety of espresso machine components. This type of gasket found boilers, brewing group and valve assemblies. The most common location for this to seal off the 3/8” male nut on the top of the Faema E61 and E61 style brewing groups like with Bezzera,...

  • 0 1 2 3 4 (0)
    1,21 € Add to cart In Stock

    This stainless steel compression spring with the dimensions of 15x25mm is normally used as a camme spring on a Faema E61 brewing group or on E61 style brewing groups.  Like with the Faema E61, Faema E61 legend, Grimac, Isomac, Pavoni, Wega and a variety of other brands which use a e61 style of brewing group. Besides that option, this model...

  • 0 1 2 3 4 (0)
    2,52 € Add to cart In Stock

    On this page you will find a camme guide bushing. This part is a generic part for Faema E61 brewing groups and the brewing groups made in the E61 style. This part is made from brass with a total length of 28mm, the outer dimensions are 15 and 10 mm. The ID is 8mm and the head of the bushing has a thickness of 5mm. This part slides over the shaft off the...

  • 0 1 2 3 4 (0)
    5,08 € Add to cart In Stock

    On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....

  • 0 1 2 3 4 (0)
    3,42 € Add to cart In Stock

    This article is one of the earliest designs of the 60mm shower screen. This shower screen is made by IMS CFDR070.  The border diameter is 60mm, it has a internal height of 15,7mm. The internal holes, 112 in total, have a diameter of 2mm Note: this is not a specialty coffee shower, but IMS also produces normal showers. This is, unlike other 60mm...

  • 0 1 2 3 4 (0)
    7,11 € Add to cart In Stock

    This ½” chrome plated stuffing nut has a central hole of 10,7mm. The item itself has a height of 17mm. You need a metric key 22 to install this item. This is quite a common key size in most peoples toolbox. But what is the function of this part and where can it be found. This threaded stuffing gland is used in the side of the Faema E61,...

  • 0 1 2 3 4 (0)
    1,17 € Add to cart In Stock

    The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...

  • 0 1 2 3 4 (0)
    4,01 € Add to cart In Stock

    This flat Polytetrafluoroethylene (PTFE) gasket 25.5x21x5mm is used on Vibiemme (GUARCASUTEPI) espresso machine brewing groups. As well in the manual lever brewing group as well for the solenoid group. This part seals off the bottom off the upper sleeve in the brewing group. If you are not sure if this item will fit your Vibiemme Domobar, Vibiemme...

  • 0 1 2 3 4 (0)
    4,02 € Add to cart In Stock

    If you want to attach a E61 style brewing group to the espresso machine there is normally a gasket inbetween the brewing group and metal frame. In this case a 2mm paper gasket with a width of 70 and a height of 80mm. This gasket type used on a variety of E61 style brewing groups from the brands: San Remo, Royal, Reneka, La Scala, Vibiemme, Grimac, Wega,...

  • 0 1 2 3 4 (0)
    1,10 € Add to cart In Stock

    This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

  • 0 1 2 3 4 (0)
    16,14 € Add to cart In Stock

    This camme rod for E61 style espresso machines is slightly different then the one used in the Faema E61. This one has a small guide pin at the end which goes inside the group. On the other side there is a squared off section for the lever arm. This section is 6x6mm. To hold the lever in place there is a M6 thread on the end for some sort of a nut. This...

  • 0 1 2 3 4 (0)
    5,29 € Add to cart In Stock

    This stainless steel cam lock prevents you from turning the camme shaft on the E61 and E61 style group too far. It has a male M6 thread on one side, the other side has a slit to screw the part in the Brewing group with a flat head screwdriver. This coffee machine parts is being used with a variety of brands like: Bezzera 7479951, Brasilia 13651.0.40.04,...

Showing 1 - 18 of 41 items
This website uses its own and third-party cookies to improve our services and show you advertising related to your preferences by analyzing your browsing habits. To give your consent to its use, press the Accept button.

Cookie preferences

Functional cookies
No
Yes
Functional cookies are strictly necessary to provide the services of the shop, as well as for its proper functioning, so it is not possible to refuse their use. They allow the user to browse through our website and use the different options or services that exist on it.
Cookie Provider Purpose Expiry
PHP_SESSIDbrooks-parts.comThe PHPSESSID cookie is native to PHP and allows websites to store serialised status data. On the website it is used to establish a user session and to pass state data through a temporary cookie, which is commonly known as a session cookie. These Cookies will only remain on your computer until you close your browser.Session
PrestaShop-#brooks-parts.comThis is a cookie used by Prestashop to store information and keep the user's session open. It stores information such as currency, language, customer ID, among other data necessary for the proper functioning of the shop.480 hours
Advertising Cookies
No
Yes
These are cookies that collect information about the advertisements shown to users of the website. They can be anonymous, if they only collect information about the advertising spaces shown without identifying the user, or personalised, if they collect personal information about the user of the shop by a third party, for the personalisation of these advertising spaces.
Analytics cookies
No
Yes
Collect information about the user's browsing experience in the shop, usually anonymously, although sometimes they also allow the user to be uniquely and unequivocally identified in order to obtain reports on the user's interests in the products or services offered by the shop.
Performance cookies
No
Yes
These are used to improve the browsing experience and optimize the operation of the shop.
Other cookies
No
Yes
These are cookies without a clear purpose or those that we are still in the process of classifying.